KT-10 TPMS sensor relearn tools Car TPMS Tire Pressure tool replace For EL-50448 ATEQ VT-30 TPMS TPMS relearn Procedure After changing TPMS sensor or changing tyre,TPMS sensor should be activated by this tools(TPMS relearn). Before activating TPMS sensors, TPMS relearn mode should be opened. For Most GM and F-o-r-d vehicles TPMS relearn mode can be open on control panel, but for some old vehicles,for example For Buick Encore,GM MDI or GM MDI2 diagnostic tools is needed to open TPMS relearn mode. For GM-Cadillac,Chevrolet,Buick Step 1 - Enter leaning mode Set the gearshift lever to "P" Put the ignition switch to “ON” Enter the interface of tire pressure display by DIC DIC shows "Press Set / Ctrl to re-learn" Press “Set / Ctrl” The turn signal is lighted for 3 seconds and the horn beep sound twice to enter the learning mode Step 2 - Read tire pressure sensor information Start from the front-left wheel, Make the J-46079 or Diagnostic Tool EL-50448 antenna up against the valve core position & close to the rim of the tire sidewall El-50448 tire pressure tool starts by the start switch Successful to read the tire pressure sensor information when the horn bleeps once Step 3 - Same method to read other tire pressure information Follow the instruction above to read tire pressure of the front-right, rear-right, rear-left wheels. Turn signals is lighted for 3 seconds and the horn bleeps twice when the learning is complete. For F-o-r-d/Lincoln 1. With vehicle off, press and release the brake pedal. 2. Using the push button, press and hold the button until the vehicle is in accessory mode (ACC mode). WARNING: DO NOT PUSH RELEASE TOO QUICKLY. PUSH – WAIT FOR SOUND – RELEASE. 3. Power off by pushing the button 1 time. 4. Repeat 2 more times, ending in ACC mode. 5. Press and release the brake pedal, then turn vehicle off. 6. Using the push button, press and hold the button until the vehicle is in accessory mode. 7. Power off by pushing the button 1 time. 8. Repeat 2 more times, ending in ACC mode. 9. Horn will sound once and TPMS telltale will blink once train mode is initiated. 10. Starting at LF tire, to keep pressing the blue button until horn chirps. Repeat procedure for remaining tires in the following order: RF, RR, and LR. If equipped with banded sensors, place antennae of learn tool on sidewall of LF tire 180 degrees from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires. 11. After successfully programming the LR tire, the message center should display “TRAINING COMPLETE’ 12. Inflate all tires to pressure listed on placard. 1. With vehicle off, press and release the brake pedal. 2. Using the push button, press once to turn on, then press again to put vehicle into ACC mode, then press again to turn vehicle off. 3. Repeat 2 more times, ending in ACC mode. 4. Press and release the brake pedal, then turn vehicle off. 5. Using the push button, press once to turn on, then press again to put vehicle into ACC mode, then press again to turn vehicle off. 6. Repeat 2 more times, ending in ACC mode. 7. Horn will sound once and TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE. 8. Starting at LF tire, to keep pressing the blue button until horn chirps. Repeat procedure for remaining tires in the following order: RF, RR, and LR. If equipped with banded sensors, place antenna of the tools on sidewall of LF tire 180 degrees from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires. 9. After successfully programming the LR tire, the message center should display “TRAINING COMPLETE” TPMS sensors application table |